HB-G100HB-G100HB-G100HB-G100 SeriesSeriesSeriesSeriesUserUserUserUser ManualManualManualManual forforforfor IntelligentIntelligentIntelligentIntellige
9InstallationInstallationInstallationInstallation &&&& WiringWiringWiringWiring DiagramDiagramDiagramDiagram ofofofof EngineeringEngin
10① Mains Supply Input: The alarm host adopts AC 220V ± 10% 50Hz input, and theinput terminal is connected in series witha0.5A fusion tube.② External
11Connection Principle: The normally open detector shall be connected in parallel witha2.7K Ω resistor, while the normally closed detector shall be co
12from damaged by mouse or other rodents.④The type and specification of detectors and cables in each defense zone should belabeled on construction dra
13intended for the host, and defense zones 000-007 are mixed wired/wireless defensezones in which it is not recommended to install wireless detectors.
14panel of the host.“ Disarm”Key: Press “ Disarm”key to disarm the host (except for shielded zone,doorbell zone and emergency zone). The function of“D
15The first four steps of deletingaremote controller are the same as those ofaddingaremote controller.Step 5: Enter 19 and # after 19, and then the ho
16【 Note 】 a. Detectors (numbered 000-119) shall be added in accordance with thesame procedure.b. To let the host learn codes of detectors continuousl
17those of addingadetector, so please refer to the first four steps of the procedure foraddingadetector.Step 5: Enter “ 010”and“*”, and then the host
18ReasonsReasonsReasonsReasons forforforfor FailingFailingFailingFailing totototo LearnLearnLearnLearn CodesCodesCodesCodesCoding Redundancy: If the w
1TableTableTableTable ofofofof ContentsContentsContentsContentsI. Definition...
196) Dialling Times: 57) Siren Duration: 30 minutes8) Leaving Time: 5 seconds9) Entry Time: 0 second10) Ringing Times Set via Remote Control: 9 times1
20② Command Function: On-site Alarm ModeCommand Grammar: 3 #Function Description: This command enables the host to work under on-sitealarm mode in whi
21again ) +“BBBBBB#”.If you have forgotten the preset password indiscreetly , you shall contact ourcustomer service centre or your local distributor f
22Step 3: Enter“10”(10 represents informed phone number) and “ #”, and then thehost will give outavoice prompt“Please enter an informed phonenumber”.S
23For the first two steps, please refer to the above mentioned procedure in SET mode.Step 3: Enter 19 and # , and then the host will warn users throug
24Press 2 5 # to select the medium on-site alarm volume;Press 2 6 # to select the large on-site alarm volumePress 2 7 # to select the maximum on-site
25② CommandCommandCommandCommand Function:Function:Function:Function: AuditionAuditionAuditionAudition thethethethe RecordRecordRecordRecordCommand Gr
26② Command Function: Set leavingtimeCommand Grammar: 3 5 # D D #Function Description: “ D D”refers to leaving time, also called delayed ARMtime and m
27⑤ Command Function: Set dialling timesCommand Grammar: 3 8 # D D #Function Description:“D D”refers to dialing times (01-99), namely howmany times th
282. Modify Alarm Mode and Arm/Disarm in SET ModeEnter # # # AA AAA A# to enter into set-up mode and modify alarm mode.① Arm the host in phone alarm m
2IntroductionIntroductionIntroductionIntroductionHB-G100 Series Intelligent Burglar Alarm Host is an intelligent long-rangewireless transmission alarm
29arm/disarm methods in "Arm/Disarm Operation" to arm the alarm host and to ensurethe system is on alert.The alarm host will automatically a
30phone numbers.4.4.4.4. RemoteRemoteRemoteRemote Set-upSet-upSet-upSet-upCallthe phone numbers pre-set for the user alarm host through fixed phone or
31Operating Conditions: -10 - 55 ℃ Relative Humidity: 40 - 70%Dial Mode: Double Audio Frequency High Frequency Group Level: -7±2dBmLow Frequency Group
32XII.XII.XII.XII. FailureFailureFailureFailure TroubleshootingTroubleshootingTroubleshootingTroubleshootingFailure Symptom Reason Failure Recovery Me
33LED “ Power Failure”indicator lights up anddisplays defense zonenumber.The battery of thedetector for this defensezone is damaged.Replace the batter
341 1 # #Delete the second group of informed phone numbers1 2 # # Delete the third group of informed phone numbers1 3 # # Delete the fourth group of i
35Warning:Warning:Warning:Warning: LimitsLimitsLimitsLimits ofofofof ThisThisThisThis SecuritySecuritySecuritySecurity SystemSystemSystemSystemAs an a
36the alarm center, or other lines are busy, so that alarm information can not betransmitted in time.8. The alarm system does not alarm when someone i
3zone) in which the host can receive shielded signals, and can not receive any alarmsignal temporarily.FullFullFullFull ArmArmArmArm It refers to the
4II.II.II.II. OperatingOperatingOperatingOperating PrecautionsPrecautionsPrecautionsPrecautions� Please carefully read this User Manual and pay more a
5security threats and 2 groups of telephone numbers of the alarm receivingcentre. The telephone numbers of the alarm receiving centre must be fixedtel
6IV.IV.IV.IV.NameNameNameName andandandand UsageUsageUsageUsage ofofofof MainMainMainMain ComponentsComponentsComponentsComponentsKeyboardKeyboardKeyb
7host gets ready for receiving alarm signals from partially armed zones within thesystem and giving out alarm.6)“RECORD”Indicator: In set-up mode, use
8minute.15) “ Emergency Zone”Indicator:“Emergency Zone”Indicator will light up only whenset-up is performed for an emergency zone. Once emergency zone
Commentaires sur ces manuels